Mercury 92-858058K01 Page 64 Manual Download

Page: 64 / 150

Section 3 - On the Water

Page 56

90-879172181

eng

FEBRUARY 2011

4. Press the "TRACK WAYPOINT" button on the Precision Pilot keypad. The "TRACK WAYPOINT" button light turns on and a

single horn beep sounds, indicating Track Waypoint engaged. Pilot tracks to the first waypoint on the chart plotter course.

Two horn beeps sound if Track Waypoint does not engage.

27701

"TRACK WAYPOINT" button

5. The VesselView "TRACK WAYPOINT" screen displays on VesselView for one second after pressing the "TRACK

WAYPOINT" button. The display shows the digital heading that the boat is traveling, the angles of the drives, and engine

speed in RPM. See

Mode Display

VesselView

NOTE: The displayed heading is based on magnetic North.

31413

Track Waypoint screen—dual engine application screen shown

NOTE: The Precision Pilot "TURN" buttons will not initiate turns when Track Waypoint mode is engaged. Turn features are

only available in Auto Heading mode.

Disengaging Track Waypoint Mode

Disengage the Track Waypoint mode by one of the following methods:
•

Press the "TRACK WAYPOINT" button on the Precision Pilot keypad. The "TRACK WAYPOINT" button light goes off and

Pilot goes to Standby. The "STANDBY" light turns on

•

Turn the steering wheel hard enough to overcome the force feedback and Pilot goes to Standby.

•

Move both ERC levers back to neutral and Pilot goes to Standby.

•

Press the "AUTO HEADING" button and Pilot goes to Auto Heading mode.

•

Turn off the chart plotter and Pilot goes to Standby.

Summary of Contents for 92-858058K01























































































































































Search results

Summary of Contents for 92-858058K01

Reviews:

Related manuals for 92-858058K01

Brands by name

Popular brands

Mercury 92-858058K01, Manual

Search results

Summary of Contents for 92-858058K01

Reviews:

Related manuals for 92-858058K01

Brands by name

Popular brands