Mercury 92-858058K01 Page 120 Manual Download

Page: 120 / 150

Section 5 - Maintenance

Page 112

90-879172181

eng

FEBRUARY 2011

Anodes and MerCathode System Locations

Description

Location

Figure

MerCathode

System

The MerCathode reference electrode and

anode are mounted to the composite cover on

the underside of the drive. The MerCathode

controller is mounted on the transmission. The

controller harness connects the components.

41249

Other sacrificial anodes, if equipped, may be mounted on the vessel to protect against galvanic corrosion. Refer to the operation

and maintenance manual provided by the boat manufacturer for additional information about vessel mounted anodes.

Other Anodes and Locations

Description

Location

Figure

Anode kit

(if equipped)

Mounted to the boat transom.

20341

Reference Electrode Wire of the MerCathode System

NOTICE

Washing the MerCathode assembly can damage components and lead to rapid corrosion. Do not use any cleaning equipment

such as brushes or high‑pressure washers to clean the MerCathode assembly.

Do not pressure‑wash the reference electrode of the MerCathode assembly. Doing so damages the coating on the reference

electrode wire and decrease the corrosion protection.

a -

Anode

b -

Reference electrode (not visible in this

view)

41163

Summary of Contents for 92-858058K01























































































































































Search results

Summary of Contents for 92-858058K01

Reviews:

Related manuals for 92-858058K01

Brands by name

Popular brands

Mercury 92-858058K01, Manual

Search results

Summary of Contents for 92-858058K01

Reviews:

Related manuals for 92-858058K01

Brands by name

Popular brands