Megger PPX30 User Manual Download Page 76 | Manualshive

Page: 76 / 84

Megger PPX30 User Manual Download Page 76

Power Pack Lifting and Shipping

The power pack is shipped as indicated by the shipping labels. Inspect the unit after shipping and notify carrier
immediately if damaged is found.

Operate and ship the power pack in the upright and vertical position, with all four wheels settled on a level service.

If the product must be shipped for any reason, the package containing the power pack must be properly labeled with
“this side up” labels to ensure the instrument is shipped in the upright vertical position.

Lifting the instrument—PPX models

PPX model power packs have two D-ring lift points on the rear or the unit secured to a reinforced metal chassis
specifically designed to allowed “top-side” lifting. The front handle of the power pack is also attached to a
reinforced metal chassis and is made of a thicker metal with holes in the handle to allow for strap clip attachment.

Fig 63:

Figure 5. PPX lift points.

Item

Description

1

Front handle hole lift points

2

Rear D-ring lift points

CAUTION: Only the “PPX” model power packs have these features, allowing them to be lifted in this manner. Do
not attempt to lift “PP” model power packs using this process.

Always remove and safely store the tester before lifting the power pack. Do not attempt to lift the power pack with
the tester sitting on top.

68

Baker Power Packs User Guide 71-061RC EN V2

www.megger.com

«
...
74
75
76
77
78
...
»

Summary of Contents for PPX30





















































































Reviews:

No comments