Mamiya 645DF User Manual Download Page 127

Page: 127 / 149

127

15.6 Hasselblad 501 CM and 503 CW without Winder

The Leaf Credo back can also be used with mechanical Hasselblad
cameras such as the 501 CM and 503 CW. These cameras are operated
in single shot mode via the shutter release button or a standard cable
release.

WARNING!

Please note that the Leaf Credo back should not be

mounted when the camera is set to

Mirror Up

. Also ensure that the lens

is not jammed or locked open on the

setting when connecting the

flash sync cable to the Leaf Credo back.

Shutter Latency Setting

While using a mechanical Hasselblad, set the latency setting to

Normal

on the Leaf Credo. When using the Mirror Up function or if you need
to rapidly press the shutter button, set the latency setting to

Zero

Precautions must be taken not to trigger the shutter too fast when using
Normal latency.

15.7 Hasselblad 503 CW with Winder CW

WARNING!

Please note that the Leaf Credo back should not be

mounted when the camera is set to Mirror Up

Make sure that the lens is

not jammed or locked open on the

setting when connecting the flash

sync cable to the Leaf Credo back.

Set the Shutter Latency to

Zero

when using a 503 CW winder with a

Leaf Credo back.

Summary of Contents for 645DF






















































































































































Search results

Summary of Contents for 645DF

Reviews:

Related manuals for 645DF

Brands by name

Popular brands

Mamiya 645DF, User Manual

Search results

Summary of Contents for 645DF

Reviews:

Related manuals for 645DF

Brands by name

Popular brands