Mamiya 645DF User Manual Download Page 101

Page: 101 / 149

101

9.14 Custom Function

The custom functions can store three different camera set-ups. When at
C-00, choose

(

), or

(

) to store a specific set of user function

selections for the group of custom settings from C-01 to C-20.

The C-00 is set to 0 which is the settings used for the default set.

Setting Custom Functions

1. Turn on the power.
2. Turn the shutter release mode lever to the

position.

3. Turn the exposure mode dial to select

(Custom Function mode).

4. Turn the rear dial to select the settings for user

, or

5. Turn the front dial to select the item you want to set.

Clear all Custom Functions

Set mode dial button to

, then press

+/-

button for 5 seconds; this

resets ALL Custom Functions to the factory default.

Setting Custom Functions to Default

1. By turning the exposure mode dial,

(custom function mode) can

be selected.

2. By turning the rear dial, user

can be selected.

3. Press and hold set button (for longer than 1 second) and settings for

can be initialized, or the settings can be returned to default.

Note:

Custom functions for the Mamiya 645DF+ and 645DF can easily

be set up and controlled via the Credo digital back.

Summary of Contents for 645DF






















































































































































Search results

Summary of Contents for 645DF

Reviews:

Related manuals for 645DF

Brands by name

Popular brands

Mamiya 645DF, User Manual

Search results

Summary of Contents for 645DF

Reviews:

Related manuals for 645DF

Brands by name

Popular brands