Mak Grills EP-429-2G, Owner'S Manual

Page: 28 / 56

Wi-FI Web Control Time Out:
Description:
This alert function will only take place if you have installed
the MAK Grills Mobile™ Wi-Fi on your Pellet Boss®. The display will read
TIME OUT and the Pellet Boss® will beep continuously for (10) ten
minutes, or until the alarm has been turned off.
What To Do:
Ÿ
Turn the alarm off by pressing any button.
Ÿ
Press the RIGHT arrow button to get to the WEB CONTROL screen.
Ÿ
Push the STAR button. WEB CONTROL will flash.
Ÿ
Use the UP button to select ON/ENABLE.
Ÿ
Press the STAR button again to accept.
Your grill should be communicating with your router at this point. Go back
into the MAK Grills Mobile™ website and confirm connectivity with the
grill.
To entirely shut off ALL audible ALARMS on the Pellet Boss®:
Ÿ
Press the UP button for (10) ten seconds to reach the maintenance
screen. The words MAKGRILL VER 3.2 (or higher) will be displayed.
Ÿ
Press the RIGHT button until you reach ALARM ENABLED.
Ÿ
Press the STAR button.
Ÿ
Use the UP button to select SILENT. Press the STAR button to accept.
Ÿ
Press and hold the UP button to exit the maintenance screen press
and hold the UP button to exit. The display screen will revert back to
SETPOINT SMOKE.
Additional Error Displays:
Check TC
Description:
Displays whenever the Pellet Boss® is not getting a signal
from the Thermocouple inside the grill. It most likely indicates that the
Thermocouple is not plugged into the Pellet Boss® or has come loose
from the back of the board.
What To Do: Remove the fan/access panel on the left end of the
barbecue body. Locate the Thermocouple connection at the upper right-
hand corner of the Pellet Boss® The cable is labeled
THERMOCOUPLE.
Gently unplug the Thermocouple from the Pellet Boss® and then plug it
back in.Turn on the grill. The GRILL TEMPERATURE should display the
actual outside ambient air temperature. If this does not solve the issue
refer to manual mode instructions on page 26.
NOTE: If this does not resolve the issue, please contact MAK Grills
Service for additional assistance.
25 26
Hopper Open
Description:
Alerts you that the pellet hopper door is open or not fully
engaging with the auger stop switch. The Pellet Boss® display will show
HOPPER OPEN.
What To Do: Close the hopper lid. If the Pellet Boss® display still says
HOPPER OPEN, check the alignment of the auger stop switch attached
to the left outside wall of the pellet hopper and the magnet on the inside
lip of the hoper lid for proper alignment.
If this still does not resolve the issue, remove the fan/access panel and
unplug the auger stop switch from the back of the Pellet Boss®. (Refer to
the Pellet Boss Rear View photo in this manual).
MANUAL MODE—In Case of Thermocouple Damage or Failure
If your Thermocouple stops working, the grill will not function properly
because it will be unable to detect the grill temperature. However, MAK
has built-in a “work around” solution with MANUAL MODE operation. You
may still cook on your grill while using this function until your replacement
Thermocouple arrives.
Settings: To enable MANUAL MODE, press and hold the STAR button
until the words MANUAL SMOKE appear on the Pellet Boss® display
screen. Press the STAR button again. The word SMOKE will begin
flashing. Use the UP or DOWN button to select from SMOKE (175F),
LOW (225F), MEDIUM (275F), MEDHIGH (350F) or GRILL (450F+).
Press the STAR button again to lock in the cooking temperature you
want. The setting selected will stop flashing and the grill will adjust to and
cook at the selected temperature.
NOTE: Because there is no working Thermocouple, the Pellet Boss®
display screen will not show the grill temperature. To return to
NORMAL MODE, press and hold the STAR button until SETPOINT
SMOKE appears on the display screen.
Screen Display: IGNITING
Description:
This screen will display whenever the igniter is operating.
Once the igniter has turned off, the display screen on the Pellet Boss®
will show the grill temperature.
Settings: There are no user settings for this feature.