Magnum Energy ME-RTR Owner'S Manual Download

Page: 74 / 80

5.0 Operation

LED

Status

Meaning

PWR

(green)

OFF

1. Inverter is disabled; 2. Router’s in Power Save

mode - press any button to activate LEDs; 3. No

power to router (check router cable or power to

inverter); or, 4. No AC power at the inverter’s AC

output terminals.

AC power is available from inverter, utility, or

generator at the inverter’s AC output terminals.

FAULT

(red)

OFF

Normal operation.

A fault condition has been detected. Check the

LCD display to

nd and correct the cause.

CHG

(green)

OFF

1. Router is in Power Save mode - press any

button to activate LEDs; or, 2. Charger off - no

utility or AC generator present.

Bulk, Absorb, Float or Equalize charge mode (see

the LCD display to determine charge status).

BLINKING,

display says

“

Charger

Standby

”

The charger is in Charger Standby mode. This

occurs when the ON/OFF CHARGER button is

pressed to disable the charger.

BLINKING,

display says

“

Full Charge

”

or “

Silent

”

The charger is in Battery Saver mode. This mode

monitors battery voltage level and only charges

if the battery voltage decreases to a low level.

Silent mode will automatically start charging

when the ReBulk setting is reached.

BLINKING,

display shows

a charging

status (i.e.,

Bulk, Absorb,

Float)

The charger current is automatically decreased

because: 1. Charger Back-off - the inverter’s

internal temperature is getting hot, current is

decreased to reduce/maintain temperature; or,

2. Low AC Input Voltage - the input AC voltage

is <85 VAC, charger is disabled to help stabilize

incoming AC voltage to prevent AC disconnect.

BLINKING,

display does

not show any

charge status

The inverter is detecting AC voltage (from utility

or an AC generator) on the inverter’s AC input

terminals.

INV

(green)

OFF

1. Inverter is disabled; or, 2. Router is in Power

Save mode - press any button to activate LED’s.

Inverter is enabled - 1. Supplying AC power on

the output; or, 2. In Standby (if both INV and

CHG LEDs are on); the inverter will automatically

supply AC power to the loads if utility or

generator power is lost.

BLINKING

Inverter is in Search mode (the AC load is below

the SETUP menu’s

02A Search Watts

setting).

5.3.5 LED Indicator Guide

The router provides the following LEDs (along with the LCD display) to assist

you in determining the operating status of your inverter/charger.

Table 5-1, LED Indicator Guide

Summary of Contents for ME-RTR

















































































Search results

Summary of Contents for ME-RTR

Reviews:

Related manuals for ME-RTR

Brands by name

Popular brands

Magnum Energy ME-RTR, Owner'S Manual

Search results

Summary of Contents for ME-RTR

Reviews:

Related manuals for ME-RTR

Brands by name

Popular brands