Magnum Energy ME-RTR Owner'S Manual Download

Page: 68 / 80

5.0 Operation

Overtemp

– This fault message indicates the inverter/charger has shut

down because the internal power components (FETs and/or Transformer)

have exceeded their safe temperature operating range. When the unit has

cooled down it will automatically restart and continue operation.

Remedy:

If the fault occurs while inverting reduce the load on

the inverter. If it occurs while charging turn down the charge

rate. If this fault happens often, ensure the inverter is not in a

hot area, has proper ventilation, and the cooling fans inside the

inverter are working.

AC Overload

- This fault message displays when the AC load on the inverter/

charger’s output has exceeded the inverter’s AC current protection limits. If the

overload condition lasts for less than 10 seconds, the unit will automatically

restart and resume operation. However, if the overload occurs for more than 10

seconds, the unit will shut down and require a manual restart.

Remedy:

This fault occurs because the connected AC loads are

larger than inverter’s output capacity, there is a wiring short on

the output, or the output wires are incorrectly installed. Once

the AC loads are reduced or the output wiring is corrected, the

inverter can be restarted after a manual restart.

High Volts AC

- This fault causes the AC input to be disabled because

a very high AC voltage (>150 VAC; or >300 volts for export inverters) has

been detected on the AC input.

Remedy:

Remove all AC power from the inverter’s AC input for

at least 15 minutes to automatically restart this fault. Ensure only

120VAC power is connected to each of the inverter’s AC inputs.

•

FAULT

PWR

CHG

INV

Overtemp

Settings/Info...

Overtemp

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green), and INV

(green) LEDs are off.

Figure 5-20, Overtemp Fault

AC Overload

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green), and INV

(green) LEDs are off.

FAULT

PWR

CHG

INV

AC Overload

Settings/Info...

Figure 5-21, AC Overload Fault

FAULT

PWR

CHG

INV

High Volts AC

Settings/Info...

High Volts AC

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green), and INV

(green) LEDs are off.

Figure 5-22, High Volts AC Fault

Summary of Contents for ME-RTR

















































































Search results

Summary of Contents for ME-RTR

Reviews:

Related manuals for ME-RTR

Brands by name

Popular brands

Magnum Energy ME-RTR, Owner'S Manual

Search results

Summary of Contents for ME-RTR

Reviews:

Related manuals for ME-RTR

Brands by name

Popular brands