Magnum Energy ME-RTR Owner'S Manual Download

Page: 29 / 80

3.0 Setup

03D AGS Temp

04E Gen Run Temp

, and

01 Temperatures

under the

TECH button.

Default setting

Fahrenheit

01E Viewing Ports:

The

Viewing Ports

menu item sets the main screen

to either automatically scroll through each connected port, or requires you

to manually select each port by pressing the PORT button. Adjusting the

seconds allows you to select how long the Port screen is displayed before

it automatically scrolls to the next screen. Range is

off-60 seconds

Default setting

Auto Roll (sec) = off

01F Aux Relay State:

Selections are

Open

Auto

, and

Close

Open

- Manually opens the Aux Relay contacts. This setting manually

controls the device connected to the Aux Relay, or tests the Aux Relay

operation.

Auto

- Uses the

Relay Close

and

Relay Open

settings from the

01G Aux

Relay V Trip

menu, and the

Close Delay

and

Open Delay

settings in the

01H Aux Relay Timing

menu to automatically control the Aux Relay.

Closed

- Manually closes the Aux Relay. This setting manually controls the

device connected to the Aux Relay, or tests the Aux Relay operation.

Default setting -

Open

Info:

When the open or closed selections are made, the Aux

Relay will open or close without any time delay.

01G Aux Relay V Trip:

This menu sets the Battery Voltage Trip point to

open and close the Aux Relay contacts. Once the battery voltage reaches

the trip point, the relay will open or close once the time set in the

01H

Aux Relay Timing

menu item is satisfied.

Relay Close

- Set this voltage to

close the Aux Relay contacts. This range

can be below or above the

Relay Open

setting depending on if you want

the Aux Relay to be

Active Low

Active High

Range is

8-17

(12 VDC),

16-34

(24 VDC) and

32-51

(48 VDC)

Relay Open

- Set this voltage to open the Aux Relay contacts. This range

can be below or above the

Relay Close

setting depending on if you want

the Aux Relay to be

Active Low

Active High

Range is

8-17

(12 VDC),

16-34

(24 VDC) and

32-51

(48 VDC)

Default settings

For both the

Relay Open

and

Relay Close

settings:

(12 VDC),

(24 VDC) and

(48 VDC).

Example - Active Low:

Set the

Relay Close

voltage below the

Relay

Open

voltage. If the

Relay Close

voltage is set at 12.0 VDC and the

Relay Open

voltage is set at 14.5 VDC, the relay would close when

the battery voltage dropped to 12.0 VDC and open when the battery

voltage rises to 14.5 VDC. This configuration might be used to control

a battery exhaust fan or as a simple PV charge controller.

Example - Active High:

Set the

Relay Open

voltage below the

Relay

Close

voltage. If the

Relay Open

voltage is set at 12.0 VDC and the

Relay Close

voltage is set at 14.5 VDC, the relay would open when

the battery voltage dropped to 12.0 VDC and close when the battery

voltage rises to 14.5 VDC. This configuration might be used to control

a low voltage disconnect circuit for a DC load.

•

Summary of Contents for ME-RTR

















































































Search results

Summary of Contents for ME-RTR

Reviews:

Related manuals for ME-RTR

Brands by name

Popular brands

Magnum Energy ME-RTR, Owner'S Manual

Search results

Summary of Contents for ME-RTR

Reviews:

Related manuals for ME-RTR

Brands by name

Popular brands