Magnum Energy ME-RTR Owner'S Manual Download Page 23

Page: 23 / 80

3.0 Setup

3.2.3 METER Button

The METER button gives you access to different meters which help determine

the status of the inverter/charger and battery system.

Info:

Some METER functions may not be accessible with older

inverter software. If some meters do not function, check for

current inverter software.

Info:

Most displays automatically return to the System Home

screen

ve minutes after the last button push. When using the

METER button, the selected menus stay and do not return to

the Home screen. This feature is useful for displaying commonly

used meter readings.

Info:

Pressing and holding down the METER button for 3 seconds

takes you back to the System Home screen from any menu.

1 DC Meters

2 AC Meters

3 AGS Meters

All Select Meter

METER Button

Press to

view meters

Press

METER

Rotate to

desired

selection:

1 DC Meters
2 AC Meters
3 AGS Meters
ALL SELECT Meter

Top line shows menu

Bottom line shows view

01A DC Volts
1 25.9 2---- 3----
4---- 5---- 6----
ALL View INV Meter

2 AC Meters
3 AGS Meters
4 BMK Meters
ALL SELECT Meter

Figure 3-4, METER Button

Summary of Contents for ME-RTR

















































































Search results

Summary of Contents for ME-RTR

Reviews:

Brands by name

Popular brands

Magnum Energy ME-RTR, Owner'S Manual

Search results

Summary of Contents for ME-RTR

Reviews:

Brands by name

Popular brands