Magnum Energy ME-RTR Owner'S Manual Download

Page: 44 / 80

3.0 Setup

When pushing the TECH button from the System Home screen, temperatures

of ALL the units connected to the router are displayed. The units display in the

order of the PORT to which they are connected (1-6).
Temperatures displayed are:

INV Batt Sensor Temp (TECH 01A)

- Displays the temperature of the

inverter’s Battery Temperature Sensor (BTS).

INV Transformer Temp (TECH 01B)

- Displays the temperature of the

inverter’s transformer.

INV FETs Temp (TECH 01C)

- Displays the temperature of the inverter’s

Field Effect Transistors (FET).

Info:

The temperatures are displayed in Celsius or Fahrenheit,

as selected in SETUP menu’s

01D Temp Display

Firmware Versions (TECH 02):

The

Firmware Versions

menu displays

ALL the units connected to the router. The unit versions display in the order

of the PORT to which they are connected (1-6).

Info:

The router version will be displayed in the lower left of

the screen of the TECH’s

Firmware Versions

menu item.

•

Press to edit

setting if

available

Press

TECH

Rotate to

desired

selection:

INV Batt Sensor Temp
1 25C 2 ---- 3----
4---- 5 ---- 6----
ALL Tech 01A

Top line shows menu

Bottom line shows port

and menu item

Inv FETs Temp

1 28C 2 ---- 3 ----
4 ---- 5 ---- 6 ----
ALL Tech 01C

Fault History

Press Select

to view

Tech 04

Load System Defaults

PRESS and HOLD KNOB

5. 0 Seconds

Tech 07

...

Figure 3-7, TECH Button

INV Batt Sensor Temp

1 25C 2 ---

3 ---

4 ---

5 ---

6 ---

ALL Tech 01A

TECH Button

Summary of Contents for ME-RTR

















































































Search results

Summary of Contents for ME-RTR

Reviews:

Related manuals for ME-RTR

Brands by name

Popular brands

Magnum Energy ME-RTR, Owner'S Manual

Search results

Summary of Contents for ME-RTR

Reviews:

Related manuals for ME-RTR

Brands by name

Popular brands