UNLOADING AND ASSEMBLY
Form # 169242
Model Year - 2009
69
(continued next page)
L1 D 1 1 5 || T R A C T O R S E T U P ?
L2 C 1 1 4 ||
N O / Y E S
C A B
D I S P L A Y
S E T U P ?
L1
D 1 1 5 || H E A D E R I N D E X
M O D E ?
L2
C 1 1 4 || R E E L &
C O N V E Y O R
L2
C 1 1 4 || R E E L
O N L Y
L1
D 1 1 5 || R E T U R N T O
C U T
M O D E ?
L2
C 1 1 4 || H E I G H T
&
T I L T
L2
C 1 1 4 || H E I G H T
O N L Y
L1
D 1 1 5 || H E A D E R A U T O
R A I S E ?
L2
C 1 1 4 ||
N O / Y E S
T I L T
C Y L I N S T A L L E D ?
L1
D 1 1 5 || A U T O R A I S E
S E T T I N G ?
L2
C 1 1 4 || 4 . 0
M I N
L2
C 1 1 4 || 1 0 . 0
M A X
L1
D 1 1 5 || T I L T C Y L
I N S T A L L E D ?
L2
C 1 1 4 ||
N O / Y E S
L1
D 1 1 5 || H D R C U T W I D T H ?
0 1 0 1
L2
C 1 1 4 || 2 0 . 5
F E E T
L1
D 1 1 5 || H A Y C O N D I T I O N E R ?
L2
C 1 1 4 ||
N O / Y E S
L1
D 1 1 5 || A U G E R H D R
R E E L
S P D
L2
C 1 1 4 ||
R P M / M P H
L2
C 1 1 4 ||
R P M / K P H
L1
D 1 1 5 || S E T T I R E
S I Z E ?
L2
C 1 1 4 || 1 8 . 4 X 2 6
T U R F
L2
C 1 1 4 || 1 8 . 4 X 2 6
B A R
L2
C 1 1 4 || 2 3 . 1 X 2 6
T U R F
L2
C 1 1 4 ||
6 0 0 - 6 5
R 2 8
L1
D 1 1 5 || S E T
E N G I N E
I S C
R P M ?
L2
C 1 1 4 ||
N O / Y E S
S E T
C O N T R O L L O C K S ?
L1
D 1 1 5 || P R E S S
H A Z A R D
T O
S E T
L2
C 1 1 4 || I S C
R P M
O F F
L1
D 1 1 5 || P R E S S
H A Z A R D
T O
S E T
L2
C 1 1 4 || I S C
R P M
2 4 0 0
L1
D 1 1 5 || E X I T
E N G I N E
I S C ?
L2
C 1 1 4 ||
N O / Y E S
P R E S S
H A Z A R D
T O
S E T
L1
D 1 1 5 || S E T C O N T R O L
L O C K S ?
L2
C 1 1 4 ||
N O / Y E S
V I E W
C O N T R O L L O C K S ?
L1
D 1 1 5 || H E A D E R
T I L T
L2
C 1 1 4 || E N A B L E D / L O C K E D
L1
D 1 1 5 || R E E L
F O R E / A F T
L2
C 1 1 4 || E N A B L E D / L O C K E D
L1
D 1 1 5 || D R A P E R
S P E E D
L2
C 1 1 4 || E N A B L E D / L O C K E D
L1
D 1 1 5 || A U G E R
S P E E D
L2
C 1 1 4 || E N A B L E D / L O C K E D
L1
D 1 1 5 || R E E L
S P E E D
L2
C 1 1 4 || E N A B L E D / L O C K E D
L1
D 1 1 5 || E X I T
C O N T R O L
L O C K S ?
L2
C 1 1 4 ||
N O / Y E S
H E A D E R T I L T
Programming Menu Flow Chart
If "NO" then jump to:
Default is NO
NO is the initial default. If "NO" then jump to:
The auto raise setting can be changed from 4.0
(minimum) to 10.0 (maximum) in 0.5
increments.
When in the programming mode the header ID will be shown on
the top line of the CDM using the last 4 display positions.
Use the "arrow" keys to set the header cut
width. The header ID appears at the RHS.
DRAPER HEADER ONLY. Default will be
flashing. Use "arrow" keys to select.
AUGER HEADER ONLY
For IMPERIAL display.
If "NO" then jump to:
If "NO" then jump to:
For METRIC display.
Pressing "SELECT" will go to the next line 1
(L1) menu selection. The turn signal "arrow"
keys are used to change the values.
If "NO" then jump to:
This menu allows the operator to selectably "lock
out" the control functions for the various header
functions. The default or selected "status" for
each item will flash.
The "arrow" keys are used to ENABLE or LOCK
OUT each function. Pressing "SELECT" will go
to the next L1 menu item.
If "NO" then jump to:
Pressing "SELECT" will go to the next line 1 (L1) selection. The
turn signal "arrow" keys are used to change the values. Pressing
"PROGRAM" at any time cancels the programming mode /
menus and returns back to the main operating display.
Sets the engine Intermediate Speed Control. The
default / last selected rpm will be displayed and
flashing. The "arrow" keys are used to cycle
between the selections.
When "SELECT" is pressed the program goes to
the EXIT ENGINE ISC? menu.
Y
E
S
Y
E
S
Y
E
S
