Lyngdorf MP-60 Owner'S Manual Download | Manualshive

Page: 35 / 43

background image

Lyngdorf Audio MP-60 – Owner’s manual

35

Manage Software

From this main menu, you can access MP-60 software information, backup, restore, etc.

Download system log

Here you can download a syslog file to your PC/MAC – this file will hold information as to the decoder and
software behavior. In case of a problem occurring, this file should be included in the correspondence for the
factory for check.

Backup

Make a complete system backup, including speaker setup and RoomPerfect™ measurements. You can
back up to an USB pen-drive or the SD card, if inserted. You can name the backup for easy identification, if
you want to be able to return to this setup after testing another setup of speakers. This file can also be used
to move the entire setup to another MP-60 processor – and it can be included in communications as to setup
issues. When the backup is complete, the MP-60 will go into standby mode.

Restore

Restore the system from a backup file. Select the backup file and start the process. When the restoring is
complete, the MP-60 will go into standby mode.

Factory Reset
Restore the system to the default factory settings.
Note: All user preference settings, system data, and RoomPerfect™ data are lost when the MP-60 is
restored to the default settings, so make a backup if you want the option of restoring to the present setup.

«
...
33
34
35
36
37
...
»

Summary of Contents for MP-60












































Reviews:

No comments

Related manuals for MP-60

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Brand: Tacx Pages: 2

Brand: C.E. Nierhoff & Co Pages: 7

Brand: IBEX Pages: 10

Brand: M-system Pages: 12

Brand: Paia Pages: 11

Brand: CAB Pages: 39

Brand: rbd instruments Pages: 18

Brand: GAPOSA Pages: 32

Biosafe 110 Port

Brand: Sartorius Pages: 2

Brand: Bowa Pages: 140

Brand: Toparc Pages: 32

Brand: SDE Lighting Pages: 7

Brand: PARAMOUNT BED Pages: 28

Brand: FOAMICO Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands