Lyngdorf MP-60 Owner'S Manual Download | Manualshive

Page: 36 / 43

background image

Lyngdorf Audio MP-60 – Owner’s manual

36

Update Software

Update from Remote Files

When connected to the Internet, the MP-60 will automatically identify new software updates from our server.

1. Select the file listed on the remote server list.
2. Press Start Update to upload the new software to the MP-60.

Update from Local Files

On the product page of

www.lyngdorf.com

you will be available to download the software file for an update of

the processor.

Via web interface:

3. Click Browse to find a file stored on your computer.
4. Press Start Update to upload the new software to the MP-60.

Or:

1.  Upload the software file to a FAT32 formatted USB pen drive.
2.  Make sure you ‘eject’ the pen drive correctly before removing it from your PC/MAC
3.  Insert the pen drive into the USB A connector on the MP-60.
4.  Browse and select the file in the menu and click Start Update

Note: System settings and RoomPerfect™ data remain intact during software updates.

«
...
34
35
36
37
38
...
»

Summary of Contents for MP-60












































Reviews:

No comments

Related manuals for MP-60

Brand: ZOLL Pages: 344

Brand: ABB Pages: 9

Brand: Raymarine Pages: 464

Brand: 3M Pages: 8

Brand: ZOLL Pages: 3

Brand: B&K Pages: 12

AJSPD850P - P2 DECK

Brand: Panasonic Pages: 73

Brand: AAON Pages: 36

Brand: Haaga Pages: 31

Brand: Kärcher Pages: 88

Brand: Nellcor Pages: 161

OXIMAX N-600X Series

Brand: Nellcor Pages: 210

Brand: OAKWORKS Pages: 24

Brand: Velleman Pages: 16

Brand: Velleman Pages: 11

AirForm Night Splint

Brand: Össur Pages: 16

Brand: Össur Pages: 17

Brand: Magicfx Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands