Lyngdorf MP-60 Owner'S Manual Download

Page: 9 / 43

Lyngdorf Audio MP-60 – Owner’s manual

Remote Control

The MP-60 comes with a dedicated remote control, which can operate both with radio frequencies (RF) and
infrared control (IR)

Setup

Access the installation menu.

Standby

Turn the MP-60 on and into standby.

Audio

Access the post-processing menu.

Trim

Access to miscellaneous audio adjustments.

Up/Down

Move up and down in menus.
Browse available settings in a menu.
Toggles between the available RoomPerfect™ filters.

Left/Right

Move left and right in menus.
Toggle between neutral and the available voicings.

Activate the info screen, indicating the status of
the unit.
Select a menu and store a selected setting.

Back

Return to the previous menu.

Menu

Access the user menu.

SRC

Access the source menu list.

Source -/+

Toggle between active sources.

Turn volume up and down.

Mute

Mute and restore the sound.

Play/Pause

Play/pause the currently playing track in the media player.

Skip Forward/

Skip in the current playlist in the media player.

Backwards

Summary of Contents for MP-60












































Search results

Summary of Contents for MP-60

Reviews:

Related manuals for MP-60

Brands by name

Popular brands

Lyngdorf MP-60, Owner'S Manual

Search results

Summary of Contents for MP-60

Reviews:

Related manuals for MP-60

Brands by name

Popular brands