LUDLUM 4525 Operator'S Manual Download Page 9

Page: 9 / 106

Model 4525 Gate Monitor

Operator’s Manual

Ludlum Measurements, Inc.

Page 1

May 2018

Introduction

The Model 4525 Radiation Portal Monitor (RPM) is a sophisticated system
with very sensitive gamma and optional neutron detectors for detecting small

amounts of radiation. The sophistication of the RPM provides the user with the
best chance of avoiding radiation. The RPM performs these functions with

minimal disruption to the normal processes of handling materials inbound and
outbound. Model 4525 systems are normally operated in a pass-through (or

drive-through) configuration with a scan occurring while the vehicle is passing
through the portal.

Several configurations are available. The most common RPMs are shown in the
photos below.

Model 4525-7000

Model4525-14000

Section

Summary of Contents for 4525











































































































Search results

Summary of Contents for 4525

Reviews:

Related manuals for 4525

Brands by name

Popular brands

LUDLUM 4525, Operator'S Manual

Search results

Summary of Contents for 4525

Reviews:

Related manuals for 4525

Brands by name

Popular brands