manualshive.com logo in svg

LUDLUM 4525, Operator'S Manual, Page: 24 / 106

Share
Download
LUDLUM 4525 Operator'S Manual Download Page 24

Model 4525 Gate Monitor 

Operator’s Manual 

Ludlum Measurements, Inc. 

Page 16 

May 2018 

    Minimum = 0ms, Maximum = 0ms, Average = 0ms 

Example of bad network communication: 

U:\>ping 192.168.200.2 

Pinging 192.168.200.2 with 32 bytes of data: 

 
Request timed out. 
Request timed out. 
Request timed out. 
Request timed out. 

Ping statistics for 192.168.200.: 
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), 
Approximate round trip times in milliseconds: 
    Minimum = 0ms, Maximum = 0ms, Average = 0ms 

Software Installation 

The software is provided on flash drive. Insert the flash drive into the computer. 
The default install location for the software will be “C:\Program Files\Ludlum 

Measurements, Inc.\Model 4525 Gate Monitor”.  

Note: 

The  64  bit  version  of  Windows  changes  the  default  install  location  to: 
“C:\Program Files (x86)\Ludlum Measurements, Inc.\Model 4525 Gate 

Monitor”.  

 

Note: 

The user must agree to the terms and conditions of the Software License 
Agreement before installing the software.  

 

The  Supervisor  software  is  installed  in:  C:\Program  Files\Ludlum 
Measurements, Inc.\Model 4525 Gate Monitor\Supervisor. 

The  Data  Viewer  software  is  installed  in:  C:\Program  Files\Ludlum 
Measurements, Inc.\Model 4525 Gate Monitor\Data Viewer. 

The  IPSetup  utility  is  installed  in:    C:\Program  Files\Ludlum  Measurements, 
Inc.\Model 4525 Gate Monitor\Supervisor. 

Summary of Contents for 4525











































































































Reviews:

No comments