manualshive.com logo in svg

LS ELECTRIC eXP2 Series, User Manual, Page: 44 / 129

Share
Download
LS ELECTRIC eXP2 Series User Manual Download Page 44

 
 
 

Chapter 4 System Configuration

 

 
 
 

 

4-13 

 

4.5 Ethernet Setting 

If you press [Ethernet Setting] button in [System Configuration] screen as follows, you can change IP to use 
Ethernet. 

 

 

[XGT Panel Setting] 

 

You can change IP address by pressing [Set] button of each IP address, Subnet Mask and Gateway. By 
pressing OK button, changed IP information is reserved. 

 

 

Remark 

 

We recommend the following method, when connecting with PC solely.   

 

 
 
 

 

If you reboot after pressing [Disable] button, the  device will not use Ethernet. In this case, booting speed gets 
faster. 
If you use Ethernet again, reboot after pressing [Enable]. 

1) XGT Panel setting 

-

IP Address : 192.168.0.10 

-

Subnet Mask: 255.255.255.0 

-

Gateway        : 192.168.0.1 

 

2) PC setting 

-

IP Address : 192.168.0.11 

-

Subnet Mask: 255.255.255.0 

-

Gateway        : 192.168.0.1 

 

Summary of Contents for eXP2 Series


































































































































Reviews:

No comments