Link Research L2102 Instruction Manual Download Page 3

Page: 3 / 48

Link XP L2102/L2104 Receiver Instruction Manual Issue 1 - October 2003 Page 3 of 48
Link Research Ltd. 23/24 Watford Metro Centre, Dwight Road, Watford, Hertfordshire, WD18 9XA, England. Tel: +44 (0) 1923 200 900
Registered in London No. 2074604

Web:

www.linkres.co.uk Fax: +44 (0) 1923 241 357

L2102 & L2104 Receiver

Instruction Manual

Down Conversion Factor .............................................................. 39

Down Conversion Attenuation........................................................ 39

L2102/L2104 Ultra Low Delay Integrated Receiver/Decoder.............................. 39

Physical.................................................................................. 39

Mounting ................................................................................ 39

Environmental .......................................................................... 39

Power.................................................................................... 39

Power Consumption ................................................................... 39

Front Panel Controls and Indicators................................................. 39

Rear Panel Connectors ................................................................ 40

Audio Output (option choice between 5 way XLR or 12-way connector block) 40

Video Outputs .......................................................................... 41

Video Inputs ............................................................................ 41

Analogue Audio Output ............................................................... 41

Input Signal Level ...................................................................... 41

3.2

Upgrading the unit ........................................................................... 42

3.2.1

Upgrading model types and options ................................................. 42

3.2.2

Keeping track of current status...................................................... 42

3.2.3

Upgrade procedure. ................................................................... 43

3.3

Block diagrams ............................................................................ 47

3.3.1 L2102/L2104 Receiver block diagram ................................................. 47

3.3.2

L3010 Down convertor block diagram............................................... 48

Summary of Contents for L2102

















































Search results

Summary of Contents for L2102

Reviews:

Related manuals for L2102

Brands by name

Popular brands

Link Research L2102, Instruction Manual

Search results

Summary of Contents for L2102

Reviews:

Related manuals for L2102

Brands by name

Popular brands