Link Research L2102 Instruction Manual Download Page 31

Page: 31 / 48

Link XP L2102/L2104 Receiver Instruction Manual Issue 1 - October 2003 Page 31 of 48
Link Research Ltd. 23/24 Watford Metro Centre, Dwight Road, Watford, Hertfordshire, WD18 9XA, England. Tel: +44 (0) 1923 200 900
Registered in London No. 2074604

Web:

www.linkres.co.uk Fax: +44 (0) 1923 241 357

L2102 & L2104 Receiver

Instruction Manual

Last Config #

None

Last configuration (memory) used.

IPFreq #.###GHz

None

The transmit frequency of the

camera transmitter is entered here.

Note that although tuning steps of

10kHz can be entered on the screen,

when the enter key is pressed the
turner locks to the nearest 125kHz

step.
If the down convertor settings in the

Unit menu are set to L3010 or L3020
(Link), the frequency is

automatically copied to the OFDM
Demod 2 menu. If the down

convertor setting is set to Other, a
frequency can be entered that does

not have to be the same as in OFDM

Demod 2.

DConvLO #.###GHz

None

The down convertor local oscillator

frequency is entered here. Where

Link down convertors are being used,

the figure is automatically entered

from a menu setting in the Unit

menu. For down convertors from

other manufacturers enter the local

oscillator frequency here: see
supporting documentation for

details.

High

Selects the local oscillator output
mix for the down convertor. Used

with Link down convertors.

LoSide Low

Low

Selects the local oscillator output
mix for the down convertor. Used

with other manufacturers’ down
convertors. See supporting

documentation.

8MHz

Channel bandwidth. Check with

local RF Authorities for appropriate

regulations.

7MHz

Channel bandwidth. Check with

local RF Authorities for appropriate

regulations.

Width #MHz

6MHz

Channel bandwidth. Check with

local RF Authorities for appropriate
regulations.

Guard ???

None

Automatically picked up from the

incoming signal. When a value is

displayed here, it is an indication

that the receiver is locked to an

incoming signal.

Automatically detected: the receiver

is not locked to any incoming signal.

Lock ##

Yes

Automatically detected: the receiver

is locked to an incoming signal.

Modulation ???

None

Automatically detected from the

incoming signal.

OFDM Demod

Carrier ???

None

Automatically detected from the

incoming signal.

Summary of Contents for L2102

















































Search results

Summary of Contents for L2102

Reviews:

Related manuals for L2102

Brands by name

Popular brands

Link Research L2102, Instruction Manual

Search results

Summary of Contents for L2102

Reviews:

Related manuals for L2102

Brands by name

Popular brands