Link Research L2102 Instruction Manual Download Page 36

Page: 36 / 48

Link XP L2102/L2104 Receiver Instruction Manual Issue 1 - October 2003 Page 36 of 48
Link Research Ltd. 23/24 Watford Metro Centre, Dwight Road, Watford, Hertfordshire, WD18 9XA, England. Tel: +44 (0) 1923 200 900
Registered in London No. 2074604

Web:

www.linkres.co.uk Fax: +44 (0) 1923 241 357

L2102 & L2104 Receiver

Instruction Manual

detected, (null) is displayed.

Off

An encrypted data stream will not be

decrypted.

Descrambling ###

EBS

Enables decryption of and EBS
encrypted data stream.

Descrambling

EBS Key ‘’

None

Enables entry of an 8 digit
hexadecimal key. The left and right

arrows allow scrolling to the left or
right in the number. The up and

down arrows enable scrolling through

the values 1 – 9 and A – F.

Single

Use this setting for a single antenna

connected to RF1.
NB – this setting is only suitable for

very short ranges where the

transmitter is static. If the
transmitter is moving around, there

may be breaks in transmission due to
flat fading of the signal.

Diversity

Two antennas are connected, one to

RF1 and one to RF2. RF3 and RF4

can also be connected in the same

way. This gives the most reliable

performance because it is not
affected by flat fading.

Dual
Diversity

Four antennas are connected, one

each to RF1, RF2, RF3 and RF4.
This acts as two independent

diversity systems.

Remux

Where more than services are input,

they can be remuxed together to

create a single output stream.

Bypass 1

For engineering use only.

Bypass 2

For engineering use only.

Bypass 3

For engineering use only.

Bypass 4

For engineering use only.

Mode ######

Test

For engineering use only.

L3010

Use this setting for a Link

manufactured down convertor. This

setting automatically enters the

correct local oscillator frequency in

the Demod menus

Other

Use this setting for other
manufacturers down convertors. The

local oscillator setting must be
manually entered in the Demod

menus.

Dconv Type #####

None

With this setting, the receiver can be
directly tuned to any UHF frequency.

Yes

Power is supplied via the downleads

to the down convertor. On the

display LNB ON is shown in the
bottom left corner.

LNB Power ###

There is no low voltage power

supplied to the down leads.

ASI

Sets ASI as the output.

Unit

Selects DVB-T modulation as the

Summary of Contents for L2102

















































Search results

Summary of Contents for L2102

Reviews:

Related manuals for L2102

Brands by name

Popular brands

Link Research L2102, Instruction Manual

Search results

Summary of Contents for L2102

Reviews:

Related manuals for L2102

Brands by name

Popular brands