Link Research L2102 Instruction Manual Download Page 14 | Manualshive

Page: 14 / 48

background image

Link XP L2102/L2104 Receiver Instruction Manual Issue 1 - October 2003 Page 14 of 48
Link Research Ltd. 23/24 Watford Metro Centre, Dwight Road, Watford, Hertfordshire, WD18 9XA, England. Tel: +44 (0) 1923 200 900
Registered in London No. 2074604

Web:

www.linkres.co.uk Fax: +44 (0) 1923 241 357

L2102 & L2104 Receiver

Instruction Manual

the outside antennas and then cover the match using the inside antennas. Movement from
one antenna coverage area to the other will be seamless.

The second way of using dual diversity is to set demodulators 1 and 2 to one frequency and

demodulators 3 and 4 to a second frequency. The system can now be used with two
different camera transmitters. Each camera transmitter will need to have a different

service name (see protocol command list type m) set so that the receiver can select

between them. In this way, it is possible to choose which camera will provide the

receiver’s output. Switching between transmitters will not be seamless as there will be

some disturbance as the source is changed.

Generally the antennas should be placed as high as possible and in the clear (see section xx

on antennas for more information). The antenna spacing is fairly critical and should be

around 20cm to gain optimum performance. If a greater spacing than 20cm is used, the

full benefits of diversity will not be obtained. A little experimentation may be needed to

find the optimum spacing in a particular environment.

Connect the receiver as shown in the diagram below. Take care to keep all cables away

from potential sources of interference and/or damage (see the section on cables for more

information).

NB

When connecting up the cables the receiver

should not

be powered up. The LNB power

may be active whilst cables are being connected and it is easy to make a short circuit. It is

very unlikely that any damage will be done because the LNB power supply is short circuit

protected, but it is better to be safe than sorry!

Audio

RF4

RF1

RF2

AC Mains

SDI

Video

RF3

Receive

antenna

L3010 Down

convertor

75 ohm

downlead

Mast

Crossbar

L2104 receiver

75 ohm

downlead

L3010 Down

convertor

Receive

antenna

20 - 100cm spacing

Receive

antenna

L3010 Down

convertor

75 ohm

downlead

Mast

Crossbar

75 ohm

downlead

L3010 Down

convertor

Receive

antenna

20 - 100cm spacing

1.3

Turning on and setting up the receiver

Fig 8 – dual diversity
system

«
...
12
13
14
15
16
...
»

Summary of Contents for L2102

















































Reviews:

No comments

Related manuals for L2102

Brand: Dish Network Pages: 18

Brand: XIEGU Pages: 48

Brand: XIEGU Pages: 13

Brand: Uconnect Pages: 123

Brand: u-blox Pages: 2

Brand: Zamel Pages: 34

Brand: Z3 Technology Pages: 16

Brand: Yaesu Pages: 80

Brand: Major Pages: 10

Brand: Aiwa Pages: 5

Brand: Navman Pages: 54

Brand: JBL Pages: 7

Brand: BW Broadcast Pages: 23

Brand: Barlow Wadley Pages: 11

Brand: AMG Pages: 8

Brand: VDO Pages: 18

Brand: F&U Pages: 23

DIGITAL TO TV DT-301

Brand: Promax Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands