Link Research L2102 Instruction Manual Download Page 38

Page: 38 / 48

Link XP L2102/L2104 Receiver Instruction Manual Issue 1 - October 2003 Page 38 of 48
Link Research Ltd. 23/24 Watford Metro Centre, Dwight Road, Watford, Hertfordshire, WD18 9XA, England. Tel: +44 (0) 1923 200 900
Registered in London No. 2074604

Web:

www.linkres.co.uk Fax: +44 (0) 1923 241 357

L2102 & L2104 Receiver

Instruction Manual

Section 3 - Technical Reference

3.1

Technical Specifications

Specifications subject to change without notice.

For the latest version go to the Link Research web site

L3010 Down-convertor

Physical

•

130 x 170 x 40mm without antenna fitted

•

0.83kg weight

•

White stove enamelled finish

•

Housing – water resistant 2-piece die cast aluminium casing

Mounting

Four holes for direct mounting to a flat surface or flat adaptor plate for universal

pole mounting brackets.

To ensure the unit is water resistant it must be mounted with the input and

output connectors facing down.

Environmental

•

-20ºC to +55ºC

Power

•

Input range 10VDC to 30VDC supplied via coaxial cable from

receiver/decoder

•

Power consumption approximately 3.5W excluding cable loss

Lower Panel Connectors

•

N-type 50

Ω

input for connection to antenna either directly or by short drop

lead

•

F-type 75

Ω

output for connection to receiver/decoder

Input

•

1.95GHz to 2.70GHz frequency range

•

<3.5dB noise figure

Output

•

470MHz to 860MHz frequency range

•

Switchable in two bands

High band from 2.31GHz to 2.70GHz

Low band from 1.95GHz to 2.34GHz

Offset from centre frequency ±16MHz in two steps of 8MHz

Input Signal Level

•

Minimum level –80dBm

Output Level

•

Up to +17dBm at P1dB dependent on setting

Summary of Contents for L2102

















































Search results

Summary of Contents for L2102

Reviews:

Related manuals for L2102

Brands by name

Popular brands

Link Research L2102, Instruction Manual

Search results

Summary of Contents for L2102

Reviews:

Related manuals for L2102

Brands by name

Popular brands