manualshive.com logo in svg

LINET OptiCare X, Instructions For Use And Technical Description

Share
Download
LINET OptiCare X Instructions For Use And Technical Description Download Page 50

                 

                 D9U003VSX-0101_00

50

10 Equipment

Product equipment depends on product configuration.

10.1 X-ray Pocket

Mattress Cover ZONED could be equipped with X-ray Pocket.

The X-ray Pocket is accesible from the left side and from the right side of the OptiCare X integrated mattress.

The X-ray Pocket is connected to the mattress cover by zip so it can be removed from the mattress cover when it is completely 

unzipped.

CAUTION!

It is forbidden to wash the X-ray Pocket in the washing machine!

Fig. Access to the X-ray Pocket (mattress cover ZONED)

To use the X-ray Pocket:

►  

Set the OptiCare X integrated mattress to MAX 

Mode.

►  

Unzip the X-ray Pocket.

►  

Insert an X-ray cassette to the X-ray Pocket.

►  

Do the X-ray images.

►  

Remove the X-ray cassette from the X-ray Pocket.

►  

Zip the X-ray Pocket.

►  

Set the OptiCare X integrated mattress to the previ

-

ous mode.

Summary of Contents for OptiCare X




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands