Lincoln 2008 MKX Owner'S Manual Download Page 94

Page: 94 / 329

Erasing HomeLink

姞

buttons

To erase the three programmed
buttons (individual buttons cannot
be erased):

•

Press and hold the two outer
HomeLink

威

buttons until the

indicator light begins to
flash-after 20 seconds. Release
both buttons. Do not hold for
longer that 30 seconds.

HomeLink

威

is now in the train (or

learning) mode and can be programmed at any time beginning with Step
1 in the

“Programming”

section.

Reprogramming a single HomeLink

姞

button

To program a device to HomeLink

威

using a HomeLink

威

button previously

trained, follow these steps:

1. Press and hold the desired HomeLink

威

button.

Do NOT

release the

button.

2. The indicator light will begin to flash after 20 seconds. Without
releasing the HomeLink

威

button, follow Step 1 in the “Programming”

section.

For questions or comments, contact HomeLink

威

www.homelink.com

1–800–355–3515.

MESSAGE CENTER

With the ignition in the RUN
position, the message center,
located on your instrument cluster,
displays important vehicle
information

through a constant

monitor of vehicle systems.

You

may select display features on the message center for a display of status.
The system will also notify you of potential vehicle problems with a
display of system warnings followed by a long indicator chime.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

Summary of Contents for 2008 MKX










































































































































































































































































































































Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands

Lincoln 2008 MKX, Owner'S Manual

Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands