Lincoln 2008 MKX Owner'S Manual Download Page 157 | Manualshive

Page: 157 / 329

background image

The driver and front passenger Belt-Minder

威

features can be

deactivated/activated by performing the following procedure:

Before following the procedure, make sure that:

•

The parking brake is set

•

The gearshift is in N (Neutral) (manual transmission)

•

The gearshift is in P (Park) (automatic transmission)

•

The ignition switch is in the OFF position

•

The driver and front passenger safety belts are unbuckled

While the design allows you to deactivate your Belt-Minder

威

, this

system is designed to improve your chances of being safely

belted and surviving an accident. We recommend you leave the
Belt-Minder

威

system activated for yourself and others who may use the

vehicle. To reduce the risk of injury, do not deactivate/activate the
Belt-Minder

威

feature while driving the vehicle.

1. Turn the ignition switch to the RUN (or ON) position. DO NOT START
THE ENGINE.

2. Wait until the safety belt warning light turns off (Approximately 1–2
minutes).

•

Step 3 must be completed within 50 seconds after the safety belt
warning light turns off.

3. For the seating position being disabled, at a moderate speed, buckle
then unbuckle the safety belt nine times, ending in the unbuckled state.
Step 3 must be completed within 50 seconds after the safety belt
warning light turns off.

•

After Step 3, the safety belt warning light will be turned on for three
seconds.

4. Within approximately seven seconds of the light turning off, buckle
then unbuckle the safety belt.

•

This will disable the Belt-Minder

威

feature for that seating position if it

is currently enabled. As confirmation, the safety belt warning light will
flash four times per second for three seconds.

•

This will enable the Belt-Minder

威

feature for that seating position if it

is currently disabled. As confirmation, the safety belt warning light will
flash four times per second for three seconds, followed by three
seconds with the light off, then followed by the safety belt warning
light flashing four times per second for three seconds again.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

156

«
...
155
156
157
158
159
...
»

Summary of Contents for 2008 MKX










































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 MKX

Brand: Daihatsu Pages: 1718

Brand: RaceChip Pages: 12

Brand: Fabbri Pages: 4

Brand: TBC Pages: 12

Brand: Prorack Pages: 14

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: H&S Pages: 32

Brand: Webasto Pages: 23

Brand: RAM Pages: 666

PerfectView LCD350

Brand: Waeco Pages: 36

Brand: Macally Pages: 10

Directechs FORD11

Brand: Directed Pages: 23

Brand: XTC Pages: 2

Camry Hybrid 2012

Brand: Toyota Pages: 62

Brand: Prorack Pages: 15

Brand: Brodit Pages: 2

Brand: Metra Electronics Pages: 8

Brand: AVURA Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands