Lincoln 2008 MKX Owner'S Manual Download Page 254

Page: 254 / 329

Removing the spare tire and jack

1. Lift the carpeted load floor panel
located in the rear of the vehicle.

2. Remove the spare tire cover (if
equipped).

3. Remove the wing nut securing
the spare tire by turning it
counterclockwise.

4. Lift and remove the temporary
spare tire from the cargo area.

5. Remove the jack assembly from
the vehicle. Loosen the bag tabs and
remove the jack and lug wrench
from the bag.

6. Fold down the wrench socket
used to loosen the lug nuts and
operate the jack.

Tire change procedure

When one of the front wheels is off the ground, the transaxle
alone will not prevent the vehicle from moving or slipping off the

jack, even if the vehicle is in P (Park).

To help prevent the vehicle from moving when you change a tire,
be sure to place the transaxle in P (Park), set the parking brake

and block (in both directions) the wheel that is diagonally opposite
(other side and end of the vehicle) to the tire being changed.

If the vehicle slips off the jack, you or someone else could be
seriously injured.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Roadside Emergencies

253

Summary of Contents for 2008 MKX










































































































































































































































































































































Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands

Lincoln 2008 MKX, Owner'S Manual

Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands