Lincoln 2008 MKX Owner'S Manual Download Page 158

Page: 158 / 329

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Important supplemental restraint system precautions

Airbags DO NOT inflate slowly or
gently and the risk of injury from a
deploying airbag is greatest close to
the trim covering the airbag module.

All occupants of the vehicle, including the driver, should always
properly wear their safety belts, even when an air bag

supplemental restraint system (SRS) is provided.

Always transport children 12 years old and under in the back
seat and always properly use appropriate child restraints.

National Highway Traffic Safety Administration (NHTSA)
recommends a minimum distance of at least 10 inches (25 cm)

between an occupant’s chest and the driver airbag module.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

157

Summary of Contents for 2008 MKX










































































































































































































































































































































Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands

Lincoln 2008 MKX, Owner'S Manual

Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands