Lincoln 2008 MKX Owner'S Manual Download Page 217

Page: 217 / 329

All Wheel Drive (AWD) vehicles:

Tow your All Wheel Drive vehicle with all four wheels on the ground or
with all four wheels off the ground using a vehicle transport trailer.

not tow your All Wheel Drive vehicle with the front wheels off
the ground (by using a tow dolly) and the rear wheels on the
ground.

This will cause damage to your AWD system. If you are using a

vehicle transport trailer, follow the instruction specified by the
equipment provider.

Note:

If you tow your vehicle with all four wheels on the ground, follow

these instructions:

•

Tow only in the forward direction

•

Release the parking brake

•

Place the transmission shift lever in Neutral (N)

•

Turn the key in the ignition to the ACC position (refer to

Starting

the

Driving

chapter). The ACC position also unlocks the steering

wheel.

•

Do not exceed 65 mph (105 km/h)

•

Start the engine and allow it to run for five minutes at the beginning
of each day and at each fuel stop.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Tires, Wheels and Loading

216

Summary of Contents for 2008 MKX










































































































































































































































































































































Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands

Lincoln 2008 MKX, Owner'S Manual

Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands