manualshive.com logo in svg

Lincoln 2008 MKX, Owner'S Manual

The Lincoln 2008 MKX is a remarkable luxury SUV that offers comfort and functionality. Enhance your driving experience by having the Quick Reference Manual at your fingertips. Download it for free at manualshive.com and discover all the amazing features and functions this vehicle has to offer.

Share
Download
background image

Depending on the type of factory installed equipment, your engine block
heater system may consume anywhere between 400 watts or 1000 watts
of energy per hour. Your factory installed block heater system does not
have a thermostat; however, maximum temperature is attained after
approximately 3 hours of operation. Block heater operation longer than 3
hours will not improve system performance and will unnecessarily use
additional electricity.

Make sure system is unplugged and properly stowed before driving the
vehicle. While not in use, make sure the protective cover seals the
prongs of the engine block heater cord plug.

BRAKES

Occasional brake noise is normal. If a metal-to-metal, continuous grinding
or continuous squeal sound is present, the brake linings may be worn-out
and should be inspected by an authorized dealer. If the vehicle has
continuous vibration or shudder in the steering wheel while braking, the
vehicle should be inspected by an authorized dealer.

Refer to

Brake system warning

light

in the

Instrument Cluster

chapter for information on the brake
system warning light.

Four-wheel anti-lock brake system (ABS)

Your vehicle is equipped with an Anti-lock Braking System (ABS). This
system helps you maintain steering control during emergency stops by
keeping the brakes from locking. Noise from the ABS pump motor and
brake pedal pulsation may be observed during ABS braking and the
brake pedal may suddenly travel a little farther as soon as ABS braking is
done and normal brake operation resumes. These are normal
characteristics of the ABS and should be no reason for concern.

Using ABS

When hard braking is required, apply continuous force on the brake
pedal; do not pump the brake pedal since this will reduce the
effectiveness of the ABS and will increase your vehicle’s stopping
distance. The ABS will be activated immediately, allowing you to retain
steering control during hard braking and on slippery surfaces. However,
the ABS does not decrease stopping distance.

P

!

BRAKE

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Driving

222

Summary of Contents for 2008 MKX










































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 MKX

Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Brand: Subaru Pages: 99
Maserati Gransport Owner'S Manual preview
Gransport
Brand: Maserati Pages: 210
OnStar liveon Owner'S Manual preview
liveon
Brand: OnStar Pages: 22
Parkeon StradaPAL Installation Manual preview
StradaPAL
Brand: Parkeon Pages: 43
GMC 2010 Tahoe Owner'S Manual preview
2010 Tahoe
Brand: GMC Pages: 120
Prime Tech H-066 User Manual preview
H-066
Brand: Prime Tech Pages: 6
Subaru 360 Sedan Service Manual preview
360 Sedan
Brand: Subaru Pages: 16
AL-KO AKS 1300 Operating Instructions Manual preview
AKS 1300
Brand: AL-KO Pages: 40
Thule 953000 Instructions Manual preview
953000
Brand: Thule Pages: 8
Rydeen BSS2 Owner'S Manual preview
BSS2
Brand: Rydeen Pages: 14
Valeo MBHL Operating Manual preview
MBHL
Brand: Valeo Pages: 29
Metra Electronics 99-8206 Installation Instructions Manual preview
99-8206
Brand: Metra Electronics Pages: 12
Monster iCarPlay Direct Connect 2000 User Manual & Warranty Information preview
iCarPlay Direct Connect 2000
Brand: Monster Pages: 66
Hyundai IONIQ HYBRID 2019 Quick Reference Manual preview
IONIQ HYBRID 2019
Brand: Hyundai Pages: 16
GMC TERRAIN 2018 Owner'S Manual preview
TERRAIN 2018
Brand: GMC Pages: 312
Toyota 2003 COROLLA Repair Manual Supplement preview
2003 COROLLA
Brand: Toyota Pages: 923
Jeep 2009 Wrangler Owenrs Manual preview
2009 Wrangler
Brand: Jeep Pages: 502
Buick 2001 Century Owner'S Manual preview
2001 Century
Brand: Buick Pages: 351

Brands by name

Popular brands

Load more brands