Lincoln 2008 MKX Owner'S Manual Download Page 28 | Manualshive

Page: 28 / 329

background image

•

Wipe discs from the center out.

Don’t:

•

Expose discs to direct sunlight or heat sources for extended periods
of time.

•

Clean using a circular motion.

CD units are designed to play commercially pressed 4.75 in (12
cm) audio compact discs only. Due to technical incompatibility,
certain recordable and re-recordable compact discs may not
function correctly when used in Ford CD players.

Do not use any irregular shaped
CDs or discs with a scratch
protection film attached.

CDs with homemade paper
(adhesive) labels should not be
inserted into the CD player as
the label may peel and cause the
CD to become jammed. It is
recommended that homemade
CDs be identified with
permanent felt tip marker rather
than adhesive labels. Ballpoint pens may damage CDs. Please
contact your authorized dealer for further information.

Audio system warranty and service

Refer to the

Warranty Guide

for audio system warranty information. If

service is necessary, see your dealer or qualified technician.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Entertainment Systems

27

«
...
26
27
28
29
30
...
»

Summary of Contents for 2008 MKX










































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 MKX

Brand: JETBAG Pages: 44

Brand: Falcon Pages: 8

Brand: Dometic GROUP Pages: 20

Brand: Phonocar Pages: 2

MAGNUM RT Series

Brand: Raptor Series Pages: 6

Brand: BMW Pages: 55

Brand: Whispbar Pages: 15

Brand: Porsche Pages: 313

Brand: Icom Pages: 20

Brand: Omix-Ada Pages: 6

Brand: Linear Logic Pages: 8

Brand: Rugged Ridge Pages: 2

A-18 TRAILER ABS

Brand: BENDIX Pages: 40

Brand: Toyota Pages: 56

Brand: Mitsubishi Pages: 362

Brand: Jaeger Pages: 16

Brand: Blue Ox Pages: 5

1995 C/K Pickup

Brand: Chevrolet Pages: 483

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands