Lincoln 2008 MKX Owner'S Manual Download Page 71

Page: 71 / 329

Function

Number of bulbs

Trade

number

Fog lamp (if equipped)

H11

Front row map lamp

1600XB

Second row dome/reading
lamp

1600XB

Rear courtesy lamp

1600XB

Visor vanity lamp - Slide
on Rail system (SOR) (if
equipped)

All replacement bulbs are clear in color except where noted.

To replace all instrument panel lights - see your authorized dealer.

* To replace these lamps - see your authorized dealer.

Replacing the interior bulbs

Check the operation of all bulbs frequently.

Replacing exterior bulbs

Check the operation of all the bulbs frequently.

Replacing headlamp bulbs

1. Make sure that the headlamp control is in the OFF position.

2. Open the hood.

3. Reach over the front bolster.

Highbeam bulb

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Lights

Summary of Contents for 2008 MKX










































































































































































































































































































































Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands

Lincoln 2008 MKX, Owner'S Manual

Search results

Summary of Contents for 2008 MKX

Reviews:

Related manuals for 2008 MKX

Brands by name

Popular brands