Lincoln 2008 MKX Owner'S Manual Download Page 182 | Manualshive

Page: 182 / 329

background image

3. Locate the correct anchor behind
the gap cover for the selected
seating position.

4. Clip the tether strap to the
anchor as shown.

If the tether strap is clipped
incorrectly, the child safety

seat may not be retained properly
in the event of a collision.

5. Install the child safety seat tightly

using the LATCH anchors or safety belts. Follow the instructions in this
chapter.

6. Tighten the child safety seat tether strap according to the
manufacturer’s instructions.

If the safety seat is not anchored properly, the risk of a child
being injured in a collision greatly increases.

Attaching safety seats with LATCH (Lower Anchors and Tethers for
Children) attachments for child seat anchors

Some child safety seats have two rigid or webbing mounted attachments
that connect to two anchors at certain seating positions in your vehicle.
This type of child seat eliminates the need to use safety belts to attach
the child seat. For forward-facing child seats, the tether strap must also
be attached to the proper tether anchor. See

Attaching safety seats with

tether straps

in this chapter.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

181

«
...
180
181
182
183
184
...
»

Summary of Contents for 2008 MKX










































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 MKX

Brand: J-Top Pages: 2

Brand: Honda Pages: 73

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

Brand: Allen Sports Pages: 2

Brand: EEZ RV Pages: 31

Porsche 911 GT3 R

Brand: iRacing Pages: 25

Brand: MASCOT Pages: 12

MCL-7000 Series

Brand: Dakota Digital Pages: 2

Brand: Volvo Pages: 284

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

Brand: BURY Pages: 2

Brand: Hyundai Pages: 11

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: NavInc Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands