Lexmark XC4100 Series User Manual Download

Page: 86 / 158

•

Always use the handholds on the printer to lift it.

•

Any cart used to move the printer must have a surface able to support the full footprint of the printer.

•

Any cart used to move the hardware options must have a surface able to support the dimensions of the
options.

•

Keep the printer in an upright position.

•

Avoid severe jarring movements.

•

Make sure that your ﬁngers are not under the printer when you set it down.

•

Make sure that there is adequate clearance around the printer.

Note:

Damage to the printer caused by improper moving is not covered by the printer warranty.

Shipping the printer

For shipping instructions, go to

http://support.lexmark.com

or contact customer support.

Saving energy and paper

Setting up power saver modes

Eco

‑

Mode

From the home screen, touch

Settings

Device

Power Management

Eco

‑

Mode

Select a setting.

Sleep mode

From the home screen, touch

Settings

Device

Power Management

Timeouts

Sleep Mode

Enter the number of minutes the printer stays idle before it enters Sleep mode.

Hibernate mode

From the home screen, touch

Settings

Device

Power Management

Timeouts

Hibernate Timeout

Select the amount of time before the printer enters hibernate mode.

Notes:

•

Make sure to wake the printer from hibernate mode before sending a print job.

•

The Embedded Web Server is disabled when the printer is in hibernate mode.

Adjusting the brightness of printer display

From the homes screen, touch

Settings

Preferences

Screen Brightness

Adjust the setting.

Maintaining the printer

Summary of Contents for XC4100 Series































































































































































Search results

Summary of Contents for XC4100 Series

Reviews:

Related manuals for XC4100 Series

Brands by name

Popular brands

Lexmark XC4100 Series, User Manual

Search results

Summary of Contents for XC4100 Series

Reviews:

Related manuals for XC4100 Series

Brands by name

Popular brands