Leroy-Somer E27 Series Installation & Maintenance Download Page 84

Page: 84 / 112

Commissioning and operation

INTORQ | BA 14.0197 | 06/2014

6.2.2

Test that the manual release functions

Fig. 16

Turning direction of the lever

Motor and brake are deenergised.
14. Suspend Bowden cable (not included in the delivery package) and pul with approx. 800 N.

- The drive must be able to be turned freely. A low residual torque is permitted.

15. Release the lever.

- Torque must be available!

The preparations for commissioning are completed.

6.3

Commissioning

1. Switch on drive system.
2. Carry out a braking test.

NOTICE

❚

The manual release is designed for activation via a Bowden cable.

❚

Releasing an individual brake circuit is only possible electrically.

DANGER

Danger: rotating parts!
The drive system must be free of loads. The motor must not run!

800N

Summary of Contents for E27 Series

















































































































Search results

Summary of Contents for E27 Series

Reviews:

Related manuals for E27 Series

Brands by name

Popular brands

Leroy-Somer E27 Series, Installation & Maintenance

Search results

Summary of Contents for E27 Series

Reviews:

Related manuals for E27 Series

Brands by name

Popular brands