Leroy-Somer E27 Series Installation & Maintenance Download Page 77

Page: 77 / 112

Electrical installation

INTORQ | BA 14.0197 | 06/2014

Electrical installation

5.1

Electrical connection

5.1.1

Important notes

DANGER

There is a risk of injury by electrical shock!

❚

Electrical connection must only be carried out by skilled personnel!

❚

Only carry out connection work when no voltage is applied (no live parts)! There is a risk of

unintended start-ups or electric shock.

NOTICE

❚

It must be ensured that the supply voltage corresponds to the name plate data.

NOTICE

❚

If an emergency stop is carried out without the required suppressor circuit, the control unit

may be destroyed.

❚

Observe the correct polarity of the suppressor circuit!

NOTICE

❚

To functionally test the individual brake circuits, the power supply must be able to be

switched off individually. For a new over energisation when switching on, it is also neces-

sary to open switches K1/K3.

❚

The protective circuitry contained in the INTORQ switching device BEG-561-

(terminals 3 and 4) is not permitted for use in the lift system. The protective circuitry

must be connected parallel to the brake coil here,

31.

Summary of Contents for E27 Series

















































































































Search results

Summary of Contents for E27 Series

Reviews:

Related manuals for E27 Series

Brands by name

Popular brands

Leroy-Somer E27 Series, Installation & Maintenance

Search results

Summary of Contents for E27 Series

Reviews:

Related manuals for E27 Series

Brands by name

Popular brands