Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 201

Page: 201 / 232

4. Install the Wi-Fi adapter card into the PCI Express slot on the system board. See “Locating parts on the

Figure 145. Installing the Wi-Fi adapter card

5. Pivot the PCI card latch and push it back in until it snaps into position.

6. If the installed Wi-Fi card module supports the Bluetooth function, use a Bluetooth cable to connect

the Bluetooth connector on the Wi-Fi adapter card to the 29-in-1 card reader connector on the system
board. See “Locating parts on the system board” on page 35.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 198.

Installing or removing the Wi-Fi antennas

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

Installing the Wi-Fi antenna

To install the Wi-Fi antenna, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

Chapter 11

Installing or replacing hardware

195

Summary of Contents for ThinkStation P500









































































































































































































































Search results

Summary of Contents for ThinkStation P500

Reviews:

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 201 / 232

Search results

Summary of Contents for ThinkStation P500

Reviews: