manualshive.com logo in svg

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 41 / 232

Share
Download
Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 41

Locating parts on the system board

Note:

Your computer comes with one of the following system boards.

ThinkStation P500

Figure 6. System board part locations

1

Front audio connector

2

Internal speaker connector

3

Optical drive fan connector

4

Memory slot

5

Memory slot

6

Memory slot

7

Memory slot

8

Cover presence switch connector (Intrusion switch

connector)

9

Thermal sensor

10

Microprocessor

11

Memory slot

12

Memory slot

13

Memory slot

14

Memory slot

15

Flex adapter slot

16

4-pin power connectors (2)

17

Front fan connector

18

Clear CMOS (Complementary Metal Oxide

Semiconductor) /Recovery jumper

19

Front-access storage enclosure control connector

20

4-pin power connector

21

Thunderbolt

™

connector

22

Front USB connector

Chapter 2

.

Product overview

35

Summary of Contents for ThinkStation P500









































































































































































































































Reviews:

No comments