manualshive.com logo in svg

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 162 / 232

Share
Download
Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 162

Installing or replacing the blind-connect assembly

Note:

The blind-connect assembly is available only when you are using the following type of storage

drive bracket.

Figure 89. Storage drive bracket supported by blind-connect assembly

To install or replace the blind-connect assembly, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 111.

3. Lay the computer on its side for easier access to the blind-connect assembly.

4. Remove the storage drive brackets to get access to the blind-connect assembly at the bottom of

the storage drive bay.

5. If you are replacing the blind-connect assembly, do the following to remove the old blind-connect

assembly:

a. Record the cable routing and cable connections, and then disconnect all cables from the system

board, the RAID card, and the flex adapter.

156

ThinkStation P500 and P700 Hardware Maintenance Manual

Summary of Contents for ThinkStation P500









































































































































































































































Reviews:

No comments