manualshive.com logo in svg

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 30 / 232

Share
Download
Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 30

1

2

PELIGRO

La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede
ser peligrosa.

Para evitar el riesgo de descarga eléctrica:

•

No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o
reconfiguración de este producto durante una tormenta eléctrica.

•

Conecte todos los cables de alimentación a tomas de corriente debidamente cableadas y
conectadas a tierra.

•

Cualquier equipo que se conecte a este producto también debe conectarse a tomas de corriente
debidamente cableadas.

•

Siempre que sea posible, utilice una sola mano para conectar o desconectar los cables de señal.

24

ThinkStation P500 and P700 Hardware Maintenance Manual

Summary of Contents for ThinkStation P500









































































































































































































































Reviews:

No comments