Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 78

Page: 78 / 232

Installing SATA or SAS hard disk drives

Ensure that your computer has the minimum number of SATA or SAS hard disk drives installed for the
following supported levels of RAID:

• RAID Level 0 - Striped disk array

– A RAID Level 0 hard disk drive group consisting of at least two hard disk drives

– Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB, 64 KB, or 128 KB

– Better performance without fault tolerance

• RAID Level 1 - Mirrored disk array

– A RAID Level 1 hard disk drive group consisting of two hard disk drives

– Improved reading performance and 100% redundancy

• RAID Level 10 - Striped and mirrored disk array (a combination of RAID Level 0 and RAID Level 1)

– A RAID Level 10 hard disk drive group consisting of four hard disk drives

– Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB, or 64 KB

• RAID Level 5 - Block-level striped disk array with distributed parity

– A RAID Level 5 hard disk drive group consisting of at least three hard disk drives

– Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB, or 64 KB

– Better performance and fault tolerance

Ensure that one of the following hard disk drive enablement modules is installed in your computer:

• If zero to four SATA hard disk drives or solid state drives are installed, no hard disk drive enablement

module is needed.

• If five SATA hard disk drives or solid state drives are installed, the SATA hard disk drive enablement

module (one to five hard disk drives) is required.

• If any SAS hard disk drives are installed, the SAS hard disk drive enablement module (one to five hard

disk drives) is required.

Configuring SATA or SAS RAID functionality with the Intel RSTe configuration utility

This section describes the information about configuring SATA or SAS RAID functionality with the Intel
RSTe configuration utility.

Note:

The Intel RSTe configuration utility assumes that your computer is installed with more than one hard

disk drive. Therefore, if only one hard disk drive is installed in your computer, the following information
does not apply.

This section provides information about the following topics:

•

“Entering the Intel RSTe configuration utility” on page 72

•

“Creating RAID volumes using the Intel RSTe configuration utility” on page 73

•

“Deleting RAID volumes using the Intel RSTe configuration utility” on page 73

•

“Resetting hard disk drives to non-RAID” on page 73

Entering the Intel RSTe configuration utility

This section provides instructions on how to enter the Intel RSTe configuration utility.

During the computer startup, follow the instructions on the screen. Press Ctrl+I to enter the Intel RSTe
configuration utility.

ThinkStation P500 and P700 Hardware Maintenance Manual

Summary of Contents for ThinkStation P500









































































































































































































































Search results

Summary of Contents for ThinkStation P500

Reviews:

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 78 / 232

Search results

Summary of Contents for ThinkStation P500

Reviews: