manualshive.com logo in svg

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 160 / 232

Share
Download
Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 160

9. Install the bracket with the new storage drive into the front-access storage enclosure, and then close the

handles on both sides of the bracket.

Note:

Ensure that the storage drive connectors are aligned with the corresponding connectors in

the front-access storage enclosure.

Figure 85. Installing the storage drive bracket

10. Pivot the front cover of the front-access storage enclosure until it snaps into position.

Figure 86. Closing the front cover of the front-access storage enclosure

11. Install the front-access storage enclosure into the optical drive bay. See “Installing or replacing a device

in the optical drive bay” on page 114.

12. Connect the signal cable, the power cable, and the front cover control cable to the front-access storage

enclosure.

154

ThinkStation P500 and P700 Hardware Maintenance Manual

Summary of Contents for ThinkStation P500









































































































































































































































Reviews:

No comments