manualshive.com logo in svg

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 126 / 232

Share
Download
Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 126

2. Lift the clip on the side of the flex module upward and slide the flex module cover to the rear of the flex

module to remove the cover.

Figure 26. Removing the flex module cover

3. If you are replacing a card reader, do the following:

a. Disconnect the card reader cable from the system board. See “Locating parts on the system board”

on page 35.

b. Pull the clip as shown to remove the card reader with the card reader retaining bracket out of the

flex module.

Figure 27. Removing the card reader in the flex module

c. Flex the four clips on the sides of the card reader retaining bracket to remove the card reader from

the bracket.

Figure 28. Removing the card reader from the card reader retaining bracket

120

ThinkStation P500 and P700 Hardware Maintenance Manual

Summary of Contents for ThinkStation P500









































































































































































































































Reviews:

No comments