manualshive.com logo in svg

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 154 / 232

Share
Download
Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 154

9. Push the metal bracket down until the tab

1

is slightly curved, and then push the bracket with the

storage drive forward as shown until the tab

1

snaps into position.

Figure 74. Installing the metal bracket into the plastic frame of the converter

10. Flex the sides of the storage drive bracket and align the four pins

1

on the bracket with the

corresponding holes in the converter.

Note:

Ensure that the circuit board faces upward and the connectors

2

face toward the front of the

bracket.

Figure 75. Installing the converter into the type

1

bracket

11. Slide the storage drive bracket with the converter into the storage drive bay.

148

ThinkStation P500 and P700 Hardware Maintenance Manual

Summary of Contents for ThinkStation P500









































































































































































































































Reviews:

No comments