Lenovo RackSwitch G8264CS Installation Manual Download Page 61

Page: 61 / 96

Chapter 4: Removing and Replacing G8264CS Components

To remove a hot-swap power supply module, complete the following steps:
1. Remove the power cord from the module’s power connector.
2. Press the release latch of the power supply module, and slide the module out of

the bay.

Attention:

Do not leave the power-supply bay empty for more than 90 seconds

while the switch is operating. Either replace the power supply module or install a
blank power filler plate.

To return the component to customer service for replacement, see

Appendix A,

“Getting Help and Technical Assistance

” on

page 79

to help you gather all the

required information that is necessary to return a component. After you remove the

component, securely pack the component for shipping.

Summary of Contents for RackSwitch G8264CS

































































































Search results

Summary of Contents for RackSwitch G8264CS

Reviews:

Related manuals for RackSwitch G8264CS

Brands by name

Popular brands

Lenovo RackSwitch G8264CS, Installation Manual

Search results

Summary of Contents for RackSwitch G8264CS

Reviews:

Related manuals for RackSwitch G8264CS

Brands by name

Popular brands