Lenovo RackSwitch G8264CS Installation Manual Download Page 27

Page: 27 / 96

Chapter 2: Switch Components

Omni Port LEDs

The Omni Port LEDs are oriented as shown in the following figure.

Figure 7. Omni Port status LEDs

Status LEDs for the Omni Ports are described in the following table.

Rear Panel

Fans

For cooling, the rear panel of the G8264CS has four bays for hot-swap fan modules.

Four fan modules are required for redundancy. When four fan modules are used, if

there is a failure of one of the fans, the switch reports the condition, the other fans

continue to run, and the switch continues to operate normally.

You can replace one failed hot-swap fan module while the switch is operating. If a

second fan fails, the switch reports the condition and shuts down to prevent

overheating.

Compatible fan options are listed in the

Lenovo Networking Catalog

Fan operation and internal temperatures are monitored. If the air temperature

exceeds a desired threshold, the environmental monitor displays warnings.

Note:

If a fan fails, the maximum operating temperature drops from +40°C (104°F)

to +35°C (95°F).

Table 7. Omni Port status LED behavior

LED

State

Functional Meaning

Mode

Steady green

Port pair is configured for FC mode

Off

Port pair is configured for Ethernet mode

Flashing green

One or both attached devices are not compatible with

the configured mode (FC or Ethernet) for the port pair

Link

Steady green

Valid link for 10 GbE, 4 Gb FC, or 8 GB FC

Off

No link

Mode

Link

Summary of Contents for RackSwitch G8264CS

































































































Search results

Summary of Contents for RackSwitch G8264CS

Reviews:

Related manuals for RackSwitch G8264CS

Brands by name

Popular brands

Lenovo RackSwitch G8264CS, Installation Manual

Search results

Summary of Contents for RackSwitch G8264CS

Reviews:

Related manuals for RackSwitch G8264CS

Brands by name

Popular brands