Lenovo RackSwitch G8264CS Installation Manual Download Page 28 | Manualshive

Page: 28 / 96

background image

28

G8264CS Installation Guide

Fan LEDs

If there is a failure of one or more fans, the front panel Fan LED flashes.

Additional Fan LED indicators are located on the rear panel of the switch, on the

individual fan modules.

The following table describes the fan module LED behavior.

Power Supply

The rear panel of the G8264CS has two bays for hot-swap power supply modules.

Each power supply module has an individual IEC 320 C14 power connector. The

power cord attaches to a universal grounded AC power source.

Compatible power options are listed in the

Lenovo Networking Catalog

Statement 5

CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.

Table 8. Fan module status LED behavior

LED State

Functional Meaning

On

Fan is operational

Off

Fan module has no power.

Flashing

Fan speed has failed. Replace the fan module.

1

2

«
...
26
27
28
29
30
...
»

Summary of Contents for RackSwitch G8264CS

































































































Reviews:

No comments

Related manuals for RackSwitch G8264CS

dominion kx III

Brand: Raritan Pages: 6

Brand: Raritan Pages: 5

DOMINION KSX II

Brand: Raritan Pages: 7

Brand: Raritan Pages: 2

Brand: 3Com Pages: 12

S7906E - Switch

Brand: 3Com Pages: 8

Brand: Kohler Pages: 170

Brand: Nobile Pages: 2

Brand: StarTech.com Pages: 16

Brand: ADC Pages: 75

Storage Networking SAN128B-6

Brand: IBM Pages: 116

Brand: Eneo Pages: 19

Brand: Banner Pages: 8

MARINCO PRO INSTALLER 771-SFD

Brand: BEP Pages: 4

Brand: Quintum Pages: 125

Brand: UNICOM Pages: 8

Brand: Avatar Technologies Pages: 9

B-520-MTRX-230-6x4+2

Brand: Binary Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands