Lenovo RackSwitch G8264CS Installation Manual Download Page 95

Page: 95 / 96

Appendix C: Technical Specifications

Switching Performance

The feature performance characteristics of the G8264CS are listed in the following

table.

Note:

The specific features supported on your switch, as well as some capacity

and performance characteristics, depend on the specific firmware installed.

For more information, see the

Application Guide

and

Command Reference

for your specific switch and its installed firmware.

Table 18. G8264CS feature performance characteristics

Feature

Characteristics

Switching architecture

Non-blocking

Throughput

1,280 Gbps full-duplex

Ethernet line rate

100%

IEEE 802.1Q VLANs

1024, with 4K VLAN IDs

Forwarding database entries

128K

Configurable interfaces

128 (static or DHCP)

ARP entries

Summary of Contents for RackSwitch G8264CS

































































































Search results

Summary of Contents for RackSwitch G8264CS

Reviews:

Related manuals for RackSwitch G8264CS

Brands by name

Popular brands

Lenovo RackSwitch G8264CS, Installation Manual

Search results

Summary of Contents for RackSwitch G8264CS

Reviews:

Related manuals for RackSwitch G8264CS

Brands by name

Popular brands