Lenovo RackSwitch G8264CS Installation Manual Download Page 94

Page: 94 / 96

G8264CS Installation Guide

Power Specifications

The power specifications for the G8264CS are listed in the following table.

Table 17. G8264CS AC power specifications

Specification

Measurement

Number of power supplies

2 (1+1 load sharing/redundant)

AC-input frequency (universal)

50/60 Hz

AC-input voltage (universal)

100–127 VAC

200–240 VAC

AC inrush current

15A

AC-input current (typical)

2.09 A (RMS) @ 120 VAC

1.10 A (RMS) @ 230 VAC

AC-input current (maximum)

2.28 A (RMS) @ 120 VAC

1.30 A (RMS) @ 230 VAC

Power supply rated output power

550 W each (front-to-rear airflow)

750 W each (rear-to-front airflow)

System power dissipation (typical)

253 W

System power dissipation (maximum)

276 W

DC-output current (typical)

20.6 A

Absolute maximum system rating

100-127V~/200-240V~, 8.9A/4.5A,

50/60Hz

Summary of Contents for RackSwitch G8264CS

































































































Search results

Summary of Contents for RackSwitch G8264CS

Reviews:

Related manuals for RackSwitch G8264CS

Brands by name

Popular brands

Lenovo RackSwitch G8264CS, Installation Manual

Search results

Summary of Contents for RackSwitch G8264CS

Reviews:

Related manuals for RackSwitch G8264CS

Brands by name

Popular brands