Kyocera Mita FS-1128MFP Operation Manual Download Page 34

Page: 34 / 192

FAX Operation (Basic)

3-2

OPERATION GUIDE

Automatic Send

General transmission using the numeric keys is explained.

Switching to the Send Screen

Press the

FAX

key. Check that the basic send

screen is displayed.

NOTE:

Depending on the settings, the Address Book

screen may appear. In this event, press

Reset

display the basic screen for sending.

Selection of Transmission Method

There are two transmission methods - memory
transmission and direct transmission. The default is
memory transmission.

To select direct transmission, use the following
procedure.

Press the

Function Menu

key.

Press the

key to select [FAX Direct

TX].

Press the

key.

Press the

key to select [On].

Press the

key.

NOTE:

In direct transmission, you can designate only

one destination for one transmission.

Ready to send.

2009/05/25 12:30

Text+Photo 200x100dpi
[Orig.Img] [FAX Res.]

Setting for Direct

transmission

Description

Off

Starts memory transmission.
After originals are scanned into memory, the communication starts.

Starts direct transmission.
Dials the receiving system, and after the communication has
started, originals are scanned.

Summary of Contents for FS-1128MFP

































































































































































































Search results

Summary of Contents for FS-1128MFP

Reviews:

Related manuals for FS-1128MFP

Brands by name

Popular brands

Kyocera Mita FS-1128MFP, Operation Manual

Search results

Summary of Contents for FS-1128MFP

Reviews:

Related manuals for FS-1128MFP

Brands by name

Popular brands